Measurement of the coolant flow rate using correlation of temperature fluctuations

The transit time of the coolant, and thus its velocity, has been measured using the temperature fluctuation at the outlet of a reactor core. An impulse response function estimation is introduced, which substitutes the widely used cross-correlation measurement technique. It is shown in theory and practice that the time delay estimation is improved when using the impulse response function instead of the cross-correlation function in parameter estimation. Extremely low velocities (down to 2 cm/sec) have been measured in a natural circulation regime in a research reactor.     

光纤荧光传感器衰减寿命的加权对数拟合法

荧光寿命的检测是荧光光学传感器的核心内容，国际上尝试了多种方法来拟合这种理论上为单指数衰减信号的荧光衰减曲线。这些方法包括非线性函数标准拟合方法。即Levenburg-Marquardt方法，以及Prony方法、FFT方法，对数拟合法等等。为了克服在实际应用中发生的信号退化，需要在测量信号衰减寿命的同时测量信号的初始强度。文章介绍了一种加权的对数拟合法，经计算机仿真及实际数据测试均可以得到和Levenburg-Marquardt方法非常接近的结果，且拟合时间大大缩短，测量稳定性大大提高。仿真测试及具体实验测试结果显示了这种方法的有效性。该方法不仅与Levenburg-Marquardt方法的偏差曲线非常相似，而且实验测得的荧光寿命与Levenburg-Marquardt方法偏差在0．2％以内。     

多码CDMA系统中联合并行干扰抵消与迭代信道估计方法

本文针对多码CDMA系统提出了一种联合并行干扰抵消与迭代信道估计方法。该方法首先通过导频符号对信道进行估计，然后使用RAKE接收机后的软信息对信道参数进行修正，最后通过并行干扰抵消(PIC)去除多码干扰(MCI)。仿真结果表明，经过多次迭代后，该方法可显著地降低多码CDMA系统的误比特率平台。本文同时还给出了信道估计质量、码道数和PIC次数对多码CDMA系统性能的影响。     

MC-CDMA系统迭代检测中的一种信道估计算法

在DS—CDMA系统中，联合译码的迭代多用户检测是克服多址干扰增加系统容量的有效方法。本文将多用户检测和译码相结合的迭代检测技术应用于MC—CDMA系统，其中，多用户检测器由串行干扰消除和其后的MMSE滤波器组成。文中提出一种时域信道估计作为迭代初始值的频域信道估计算法，比单纯的频域信道估计方法节约导频符号数量，并且由于信道估计性能的改善，加快了迭代检测的收敛速度。     

Time and cost securing in complex large-scale projects

Meeting time and cost objectives in complex projects involves specific problems and risks. An attempt is made to analyse the components of total cost increase of a project caused by time delay. An outline is given as to how these considerations can be used to estimate cost increases in investors' decision situations as well as to ascertain fair contractual penalties and claims for compensation and for the evaluation of justified project acceleration costs.     

Frequency domain identification of Wiener models

This paper proposes a frequency domain algorithm for Wiener model identifications based on exploring the fundamental frequency and harmonics generated by the unknown nonlinearity. The convergence of the algorithm is established in the presence of white noise. No a priori knowledge of the structure of the nonlinearity is required and the linear part can be nonparametric.     

Markov analysis of qualitative dynamics1

Common sense sometimes predicts events to be likely or unlikely rather than merely possible. We extend methods of qualitative reasoning to predict the relative likelihoods of possible qualitative behaviors by viewing the dynamics of a system as a Markov chain over its transition graph. This involves adding qualitative or quantitative estimates of transition probabilities to each of the transitions and applying the standard theory of Markov chains to distinguish persistent states from transient states and to calculate recurrence times, settling times, and probabilities for ending up in each state. Much of the analysis depends solely on qualitative estimates of transition probabilities, which follow directly from theoretical considerations and which lead to qualitative predictions about entire classes of systems. Quantitative estimates for specific systems are derived empirically and lead to qualitative and quantitative conclusions, most of which are insensitive to small perturbations in the estimated transition probabilities. The algorithms are straightforward and efficient.     

A direct estimate of JIc from the load versus load-line displacement record

The purpose of this study is to examine the current standard fracture toughness test procedure to determine if there could be an easier method to get a J_Ic value from the test record. The current method for determining J_Ic involves a detailed computational and construction procedure. The objective in this study is to simplify the analysis for the determination of J_Ic. The results of this study show that the load and displacement record for a fracture toughness test can be used to directly estimate a J_Q value, a provisional value for fracture toughness, J_Ic. The J value taken at the maximum load point can be used along with an adjustment factor to estimate a J_Q value. This J_Q estimate is close to the one obtained from the construction procedure of ASTM Standard E 1820. When a unit‐sized specimen is tested, that is, a specimen with a width of 50 mm and a thickness of 25 mm the maximum load point provides a direct estimate of J_Q. Other sizes require a size adjustment factor, which is simply a square root relationship between the width of the test specimen and a unit width. The proposed new method of estimating J_Q is simple in concept and requires a minimum number of calculations. It appears to produce values of J_Q which are comparable to those obtained from the ASTM E1820 construction procedure and may produce less scatter.     

ISIS全局优化多道反演技术在墩2块岩性油藏描述中的应用

为进一步落实墩2块戴一段岩性油藏成藏规模及分布规律，针对该储层薄、横向变化快的特点，利用ISIS全局优化多道反演技术，对该构造区岩性储层进行了精细描述，较好的预测出戴一段储层平面分布规律。